Futaba BPS-1 RPM Sensor Manual de usuario

Busca en linea o descarga Manual de usuario para Hardware Futaba BPS-1 RPM Sensor. Futaba BPS-1 RPM Sensor User Manual [en] Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 1
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 0
Overall length: approx. 655mm
Weight: 8g
BPS-1
The BPS-1 is designed for use with
Futaba GY701, CGY750, and GV-1
governors.
The BPS-1 can be used only with a
BPS-1 compatible engine backplate.
󾛽
WARNING
󾛹
Always use the BPS-1 with a BPS-1
compatible engine backplate.
󾛹
Be careful of the connector polarity.
Because of the case construction, reversing the polarity
may cause trouble or sparking from the wiring.
󾛹
Mount the BPS-1 when the engine is
sufficiently cool.
If you touch the engine immediately after use, you may
receive a burn.
󾛹
Mount the sensor in accordance
w i t h t h e i n s t a l l a t i o n m e t h o d
described below.
If the BPS-1 drops out during flight, it cases erratic
operation or loss of control.
󾛹
Vibration-proof the PC board and
mount the BPS-1 where it will not be
exposed to fuel and water.
Electronic parts are used at the PC board. Take
protective measures against vibration, shock, high
temperature, and so forth.
󾛹
When mounting the BPS-1 to the
fuselage, be sure there is some
slack in the wiring cable.
If the cable is too tight, vibration may cause the wire
to break or the connector to be dislodged and cause a
malfunction.
󾛹
Always perform an operation check
after assembling.
Do not fly until inspection is complete.
󾛻
Do not use the BPS-1 with anything
other than an R/C model helicopter.
Sensor
PCBoard
Grommet
Connector
Sensor mounting
section
Silicone adhesive
Insert sensor
perpendicularly
Make the grommet
direction like this.
OK at more than 60% by
rotating the starter.
After assembling is complete, check operation as follows:
󾛽
WARNING
󾛹
Push in fully.
Special engine
backplate
Special engine
backplate
To engine
backplate
To Governor
BPS-1
1
Degrease the engine backplate with
alcohol, etc.
1
Connect the sensor to the governor
used and call the governor revolution
sensor test screen. (Revolution sensor
monitor for the GV-1.)
2
Using a starter, rotate the engine
without starting it and check if the
sensitivity is 60% or greater.
2
Inject silicone resin into the special
engine backplate up to about 1/3
(approximately 0.3cc) from the bottom
of the sensor mounting section of the
backplate.
3
Insert the sensor perpendicularly and
push in the grommet fully.
4
Wipe off the squeezed out adhesive.
5
Fasten the grommet so that it will
not move and allow the adhesive to
harden.
*Oil residue on the backplate will
 
cause faulty adhesion.
*
Use non-solvent alcohol-release type silicone
adhesive.
*Until adhesive is squeezed out from the
grommet is a sufcient.
*Connect and operate the sensor in accordance
with the governor instruction manual.
*Rotate with only the starter without plug
heater attached.
*If the sensitivity is less than 60%, re-check the
installation.
*So that the adhesive does not enter the engine.
Adhesive in the engine will cause engine
trouble.
Thank you for purchasing a BPS-1 Backplate Sensor
for governor. Before using your new sensor, please
read this manual together with the instruction manuals
of the governor, transmitter, and engine used and use
the BPS-1 properly. After reading this manual, store it
in a safe place.
Backplate Sensor For
Governor
1M23N25101
BPS-1
Operation Check
Installation Method
Instruction Manual
FUTABA CORPORATION
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan
Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
©FUTABA CORPORATION 2011, 3 (1)
Vista de pagina 0
1

Indice de contenidos

Pagina 1 - Instruction Manual

Overall length: approx. 655mm Weight: 8gBPS-1●The BPS-1 is designed for use with Futaba GY701, CGY750, and GV-1 governors.●The BPS-1 can be used o

Comentarios a estos manuales

Sin comentarios