Futaba SBS-01G Manual de usuario descargar pdf

SBS-01G

LED(Inside)

To telemetry receiver

S.BUS2 port

Location

LED Indication

Slot number setup

ID number

Wiring

Mounting Precautions

Relative distance/altitude

SBS-01G computes distance

and speed from GPS. It is not

recommended to be used in an

indoor ying environment. Moreover,

it may not be able to the flight

posture of a model (inverted etc.). This

sensor calculates the altitude from

atmospheric pressure. Atmospheric

pressure will get lower as you go up

in altitude, using this the sensor will

estimate the altitude. An exact display

cannot be performed if atmospheric

pressure changes in a weather. A short

time is required until the positioning

of the GPS is established. In the

meantime, don't move the model

during this process.

Do not install in a location where the wind/

air ow can hit the sensor. Also, do not put

in a sealed location where atmospheric

pressure will not change in a sealed location.

Moreover, the thing which interrupts an

electric wave must not be above a sensor

(metal, carbon).

Do not install in a

location where the

wind/air flow can hit

the sensor.

Nothing that interrupts

an electric wave must

be above the upper part

of a sensor.

It is not recommended

to be used in an indoor

flying environment.

Do not put in a

sealed location.

Data when a power supply is turned on shall

be 0m, and it displays the distance/altitude

which changed from there.

Even if the altitude of your aireld is high, it

will start at 0m and the altitude difference

from the aireld is displayed.

Please note that the proper default

slot for this accessory is number 8 (8-

15). This sensor uses eight slots. Being

made to a start slot are 8, 16, and 24.

Information on how to change the

slot assignment is included in the

transmitter's manual.

There is an ID number in SBS-01G. ID

will be unnecessary if one GPS sensor

is carried in a model. ID is needed if

there is a schedule which carries two

or more GPS sensors in one set of on

model. However, the ID number is

indicated at the bottom of SBS-01G.

The SBS-01G may only be used with

telemetry enabled receivers that offer

S.BUS 2 port. Please refer to the manual(s)

that accompanied your transmitter and/or

receiver for proper connection methodology.

Up side

It sticks on

the upward

smooth side

of the　

model using

double-stick

tape.

to S.BUS2

port

Receiver

Battery

Wind

SBS-01G

Telemetry GPS sensor

1M23N26705

Instruction Manual

Thank you for purchasing Futaba's

SBS-01G GPS sensor. This sensor, used

in conjunction with a telemetry enabled

transmitter/receiver, is used to indicate

the distance/speed/altitude of the item

to which it is attached. To maximize

your enjoyment, and to ensure proper

sensing, please read through this manual

thoroughly. We also encourage you to

retain the manual for future reference

should the need arise.

●

The SBS-01G is designed for

use with Futaba telemetry systems.

󾛽

WARNING

Failure to follow these safety precautions

may result in severe injury to yourself and

others.

󾛹

To utilize the SBS-01G GPS sen-

sor, connect it to the S.BUS2 port of

the Futaba telemetry enabled receiv-

ers.

・

The SBS-01G will not function properly if

connected to an S.BUS port or other channel

ports.

󾛹

Ensure that the unit is connected

properly to the receiver. Failure to do

so could result in damage to the sen-

sor.

󾛻

Do not use the SBS-01G with any-

thing other than an R/C model.

󾛹

Ensure that the unit is mounted in

an area that will eliminate exposure

to fuel, water and vibration.

・

As with any electronic components, proper

precautions are urged to prolong the life and

increase the performance of the SBS-01G.

󾛹

To ensure that the SBS-01G is

functioning as desired, please test

accordingly.　

・

Do not y until inspection is complete.

󾛹

Allow a slight amount of slack in

the SBS-01G cables and fasten them

at a suitable location to prevent any

damage from vibration during ﬂight.

FUTABA CORPORATION

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan

Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

Green Normal operation

Green blink GPS un-receiving

Red No signal reception

Green/Red When setting up the slot

Green/Red

Alternate blink

Unrecoverable error

Distance

Speed

Metal/Carbon

Use ： GPS/Altitude sensor (from atmospheric

pressure) with Vario meter

Range：[Speed] About 0km/h~500km/h (~311mph)

[Altitude] About -700m~5,500m

(-766yard~6015yard) ---sensor spec

[Vario meter] About -150m/s~+150m/s

(-336mph~+336mph)

Length：175mm

Weight：11g

Voltage ： DC 3.7V ～ 7.4V

Distance 1

Indice de contenidos

Pagina 1 - Distance

SBS-01GLED(Inside)To telemetry receiver S.BUS2 portLocationLED IndicationSlot number setupID numberWiringMounting PrecautionsRelative distance/altitud

Comentarios a estos manuales

Sin comentarios

Futaba SBS-01G Manual de usuario

Busca en linea o descarga Manual de usuario para Hardware Futaba SBS-01G. Futaba SBS-01G User Manual [fr] Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware Futaba SBS-01G