Futaba CDR-5000 Charger Manual de usuario

2Do not leave the CDR-5000 unattended while using it.Stop charging/discharging as soon as you notice any abnormality. In addition, stopcharging/discha

11CDR-5000 FunctionsUse "Graph" or " " key toadvance to the next screenand use " " key for reverse.

12CDR-5000 FunctionsOpening ScreenConnect the input cord of CDR-5000 to a power source, and then CDR-5000 will be automaticallyturned on and show its

13CDR-5000 FunctionsInitial-Setting ScreenHere you can set the following conditions. After completion of INITIAL-SETTING, change the screento DX DATA

14CDR-5000 Functions<Setting mode>ON: If the thermo stand detects the temperature over 40 degrees Celsius, the next cycle ofcharging/discharging

15CDR-5000 FunctionsCharging/Discharging1. Setting Parameters for Charging/DischargingCaution: Before connecting a battery to charge/discharge it to C

16CDR-5000 FunctionsItems in the SET-UP screenCaution: The setting should be carried out taking into consideration the types of batter-ies and the num

17CDR-5000 FunctionsCYCLE MODEThis is to set the number of cycles of charging/discharging at DX. 1 TIME means one cycle of acharging and a discharging

18CDR-5000 FunctionsCELL NUMBERThis is to set the number of battery cells that are connected to DX. Set "AUTO" or any number between1 and 36

19CDR-5000 Functions2. Connecting BatteryCaution: Never charge or discharge any batteries other than NiCd and NiMH batteries.Charging or discharging t

20CDR-5000 Functions•Terminal Harness*Connect Terminal Harness as shown here.DX Terminal /Terminal Harness•DX Terminal (-)*Black: negative•DX Termina

3TABLE OF CONTENTSFor Your Safety ... 4Meaning of Special Markings ...

21CDR-5000 Functions3. Start of Charging/Discharging[Charging at DX]1)Push "DX CHG" key.2)The red LED of "DX Charging" turns on. M

22CDR-5000 Functions4. End of Charging/Discharging[End of charging at DX]Alarm buzzer will beep as soon as charging at DX is over. And "FINISHED

23CDR-5000 Functions[End of discharging at DX]Alarm buzzer will beep as soon as discharging at DX is over. And "FINISHED DX DISCHARGE"screen

24CDR-5000 Functions[End of charging at RX/TX]Alarm buzzer will beep as soon as the charging at TX/RX port is over without fail after detecting"D

25CDR-5000 Functions5. Cycle Charging/Discharging[Cycle Charging/Discharging at DX]1)Push "DX CYCLE" key.2)Either the blue LED of "DX D

26CDR-5000 Functions6. Compulsively End of Charging/Discharging[How to stop charging on the way at DX]Push any one of the keys of "DX CHG",

27CDR-5000 FunctionsOver Current ProtectionAlthough the values of charging and discharging current can be set in the "SET-UP" screen, the ac

28CDR-5000 FunctionsData ScreenUp to ten of "DATA" screens including the data of charging and discharging can be memorized from thestart and

29CDR-5000 FunctionsDELAY: CDR-5000 in cycle mode is now waiting to restart again because the temperature measured by the ThermoStand is still over 40

30CDR-5000 FunctionsOUTSIDE TEMP.This shows the temperature measured by Thermo Sensor utilized in CDR-5000.HUMIDThis shows the humidity near the CDR-5

4For Your SafetyFor Your SafetyMeaning of Special MarkingsPay special attention to safety where indicated by the following marks:•Procedures which may

31CDR-5000 FunctionsMIDDLE STAGEThis shows the estimated average voltage of a battery at a middle stage of discharging process by usingthe time consum

32CDR-5000 Functions2. TX & RX DATA Screen[TX&RX DATA --]TX&RX DATA 01 though 10 represent the data used for TX&RX port. (*TX&RX D

33CDR-5000 FunctionsPEAK VOLT.This shows the peak voltage of a battery that is obtained while the battery is charged. Or the voltage ofthe battery to

34CDR-5000 FunctionsGraph ScreenGraphs are available for the data of charging or discharging under operation at DX or the data of theend of the last o

35CDR-5000 FunctionsPushing " " and " " keys simultaneously will erase the cursor and move back to the screen of"AVE", &

36CDR-5000 FunctionsPushing " " and " " keys simultaneously will erase the cursor and move back to the screen of"AVE", &

37CDR-5000 Functions[GRAPH Screen Page 4 (DIS 6-V/Time)]Pushing "Graph" or " " key in the "GRAPH Screen Page3" will show

38CDR-5000 Functions[GRAPH Screen Page 6 (CHG 6-AV/CELL)]Pushing "Graph" or " " key in the "GRAPH Screen Page5" will sho

39CDR-5000 FunctionsV: output voltageB,T: temperature of the batteryCELL numbers (1-6) are shown at the second line from the bottom on the screen.At t

40CDR-5000 FunctionsAt the bottom:AVE : average discharging voltage for all cells.TIME : discharging timeAt the right on the screen:POWER: Power level

5For Your SafetyDo not connect more than one set of battery package to the output terminal of theCDR-5000.*It is extremely dangerous to do so because

41CDR-5000 FunctionsPlease check once again !!Warning Screen"RELAY DAMAGE SERVICE 01!"Relays used in CDR-5000 are out of order due to some r

42CDR-5000 Functions"DISCHARGE AMPERE IS TOO HIGH!"This message appears when a discharging current is set at between 10A and 40A for "S

43ReferenceReference*Specifications and ratings are subject to change without prior notice.Specifications•BatteriesNiCd / NIMH batteries•Input voltage

44ReferenceOption PartsThermo StandThis is designed for measuring the temperature of a battery of 6 cells or less for motors that are beingcharged or

6For Your SafetyBe sure to spread the stand of CDR-5000 to lift its body from the ground, table, etc.*Charging and/or discharging without spreading th

7Before UsingBefore UsingFeatures• The linear current charger with advanced peak detector and automatic cutoff circuit with MOSFETcan charge battery u

8Before UsingSet Contents/NomenclaturePlease check the contents of your shipment comparing to the parts shown here.If you believe that you are missing

9Before UsingCords equipped withCDR-5000•Input clips*Connect these to the power source. Besure to connect in the proper polarity.Red: positive, Black:

10CDR-5000 FunctionsCDR-5000 FunctionsMap of FunctionsConnect the input cords of CDR-5000 to the power sourceand switch on the power source, and then