Futaba SBC-1 Manual de usuario descargar pdf

󾙏

CAUTION

󾙋

Connect the servo and battery connector in the correct polarity. Connecting the power + and -

polarities in reverse by mistake may cause smoke, ﬁre, and damage.

󾙍

Do not connect a device other than an S.BUS servo or S.BUS decoder to the S.BUS servo

connection port. If a conventional radio control servo is connected to the S.BUS servo connection

port, the servo may operate erroneously.

󾙍

Do not disassemble or modify this product. Futaba Corp. will not be responsible for any

disassembly or modiﬁcation other than those speciﬁed by us.

Futaba Corp. will not be responsible for damage caused by combination

with other than Futaba Genuine parts.

S.BUS System

Channel Changer

INSTRUCTION MANUAL

Thank you for purchasing an

SBC-1

S.BUS

channel

changer.

This product is a tool for setting the channel to

S.BUS

servo and

S.BUS

decoder of Futaba

S.BUS

system.

S.BUS

: Serial communication system for Futaba R/C system

SBC-1

Before using your new SBC-1, please read this manual

thoroughly and use the system properly and safely.

After reading this manual, store it in a safe place.

Connect an

S.BUS

servo to the

S.BUS

servo

connection port (

S.BUS

Connect a battery to the battery connection

port (

BATT.

)

LED Status

Blinks slowly

(approximately 1

time/second)

When the

CHANNEL SELECT

switch

No. and the channel set at the

S.BUS

servo are different.

Lights steadily

When the

CHANNEL SELECT

switch

No. and the channel set at the

S.BUS

servo are the same.

Set the

CHANNEL SELECT

switch No. to the

channel you want to set at the

S.BUS

servo.

Hold down the set switch (

(Approximately 1 second)

During channel setting, the LED blinks rapidly

(approximately 5 times/second) and then lights steadily.

* When the LED lights steadily, channel setting is

complete.

Remove the battery.

Remove the

S.BUS

servo.

Refer to the instruction manual of each device for

a description of the channel setting method of the

S.BUS

compatible devices (

S.BUS

decoder, etc.)

other than a servo.

When channel setting cannot be performed

correctly because of improper connection of the

S.BUS

servo or the

S.BUS

decoder, etc., the

SBC-1

is in error mode and the

LED

continuously blinks

rapidly (about 5 times/second).

LED Status

Blinks rapidly

(about 5 times/

second)

When channel setting cannot be

performed correctly.

In this case, check the following:

manual are subject to change without prior notice. While this manual has been carefully written, there may be inadvertent

errors or omissions. Please contact our service center if you feel that any corrections or clariﬁcations should be made.

FUTABA CORPORATION Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba 299-4395, Japan

1M23N23101 ©FUTABA CORPORATION 2010, 2 (1)

Meaning of Special Markings

Pay special attention to safety where indicated by the following marks:

󾙏

DANGER

Procedures which may lead to dangerous conditions and

cause death/serious injury if not carried out properly.

󾙏

WARNING

Procedures which may lead to a dangerous condition

or cause death or serious injury to the user if not carried

out properly, or procedures where the probability of

superﬁcial injury or physical damage is high.

󾙏

CAUTION

Procedures where the possibility of serious injury to the

user is small, but there is a danger of injury, or physical

damage, if not carried out properly.



󾙍

= Prohibited

󾙋

= Mandatory

Usage Precautions

Name of Each Part and Accessories

Applicable items:

S.BUS servo, S.BUS decoder

[SBC-1 Ratings]

•Dimensions:1.54x1.02x0.39in.

 (39x26x10mm)

•Weight:0.28oz.(7.8g)

•Power requirement: Ni-Cd, Ni-

MH4cellsto5cellsequivalent

battery (Futaba)

•Operating temperature range:

-10to+45°

operation will become impossible. In this case,

reconnectthepowersourcebeforereuse.

•

C h a n n e l s e t t i n g c a n n o t b e p e r f o r m e d

simultaneously at multiple S.BUSservos.Always

connect only one S.BUSservototheSBC-1.

If multiple S.BUS servos are connected using

a Y-harness, etc., channel setting will not be

performedatanyS.BUSservo.

Channel select

switch

Set switch

Status display

LED (red)

Dust cover x2

(Vacant connectors)

S.BUS servo connection port

Battery connection port

󾙏

CAUTION

󾙍

To prevent the entry of foreign

matter, do not remove the

connector dust cover of the vacant

connectors. Channel setting cannot

be performed at the connector under

the cover.

(S.BUS)

(BATT.)

Signal

(white wire)

+ (red wire)

– (black wire)

(No connection)

Mini screwdriver

•Usetheminiaturescrewdrivertooperatethe

channel select switch and the set switch.

Instruction manual (this manual)

Channel Setting

Errors

Check items

•

Isabatteryconnectedtothebatteryconnection

port?

•

Is an S.BUS servo or S.BUS decoder connected

to the S.BUSservoconnectionport?

•

Are the battery and S.BUS servo connectors

rmlyinsertedfully?

•

ArethebatteryandS.BUS s er v o c ab les

damaged, broken, etc?

•

Isthebatterycharged?

Precautions

•

Do not connect the power source with the SW

presseddown.Ifthepowersourceisconnected

when the SW is pressed, the LED will light and

Usage Precautions 1
Channel Setting 1

Indice de contenidos

Pagina 1 - Channel Setting

󾙏CAUTION󾙋 Connect the servo and battery connector in the correct polarity. Connecting the power + and - polarities in reverse by mistake may cause smo

Comentarios a estos manuales

Sin comentarios

Futaba SBC-1 Manual de usuario

Busca en linea o descarga Manual de usuario para Hardware Futaba SBC-1. Futaba SBC-1 User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware Futaba SBC-1