Futaba SBS-01T Manual de usuario

Busca en linea o descarga Manual de usuario para Hardware Futaba SBS-01T. Futaba SBS-01T User Manual Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 1
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 0
<表面>
<裏面>
Telemetry SystemTelemetry System
●用途 温度センサー
●測定範囲 -20℃~ 200℃
●全長 535mm●重量 4.7g
●電圧 DC3.7 7.4V
温度センサー
MADE IN TAIWAN
Temperature Sensor
1M25A11701
4 513886 306273
00106836-1
SBS-01T-01
Temperature Sensor
Temperature Sensor
INSTRUCTION MANUAL
Temperature sensor
LED
to telemetry receiver
S.BUS2 Port
Temperature
detection part
Please take care to ensure that the
only portion of the temperature
sensor that touches the desired
surface (cylinder head, motor can,
etc.) is the sensing unit itself as
indicated in the image below.
To prevent damage, do not allow
the remaining parts of the SBS-01T
to touch the areas that will become
hot.
Green--Normal operation
Red--No signal reception
Green/Red--When setting
up the slot
Green/Red Alternate blink
--Unrecoverable error
Mounting Precautions
The SBS-01T may only be used with telemetry
enabled receivers that offer S.BUS 2 port(s).
Please refer to the manual(s) that accompanied
your transmitter and/or receiver for proper
connection methodology. Please note that the
proper default slot for this accessory is number
one. Information on how to change the slot
assignment is included in the transmitter's manual.
Receiver connection / Slot
number
setup
LED Indication
Thank you for purchasing Futaba's
SBS-01T Temperature Sensor.
This sensor, used in conjunction
with a telemetry enabled transmitter/receiver, is used to indicate
the operating temperatures of the item to which it is attached.
To maximize your enjoyment, and to ensure proper sensing,
please read through this manual thoroughly. We also encourage
you to retain the manual for future reference should the need
arise.
The maximum operating temperature for the SBS-01T
is 200.
If used in applications that exceed the maximum operating
temperature there is the risk of damaging the unit.
Ensure that the unit is mounted in an area that will
eliminate exposure to fuel, water and vibration.
As with any electronic components, proper precautions are urged to prolong the
life and increase the performance of the SBS-01T.
To ensure that the SBS-01T is functioning as desired,
please test accordingly.
Do not fly until inspection is complete.
Allow a slight amount of slack in the SBS-01T cables
and fasten them at a suitable location to prevent any
damage from vibration during flight.
Futaba Service Center
3002 N Apollo Drive Suite 1, Champaign, IL 61822
U.S.A.
TEL (217)398-8970 or E-mail: [email protected]
(Support)
WARNING WARNING
To utilize the SBS-01T temperature sensor, connect it
to the S.BUS2 port of the Futaba telemetry enabled
receivers.
The SBS-01T will not function properly if connected to an
S.BUS port or other channel ports.
Do not use the SBS-01T with anything other than an
R/C model.
Ensure that the unit is connected properly to the
receiver. Failure to do so could result in damage to
the sensor.
To prevent any burns, always mount the SBS-01T to
the engine after it has completely cooled.
Vista de pagina 0
1

Indice de contenidos

Pagina 1 - WARNING WARNING

<表面><裏面>Telemetry SystemTelemetry System●用途 : 温度センサー●測定範囲 : -20℃~ 200℃●全長 : 535mm●重量 : 4.7g●電圧 : DC3.7 ~ 7.4V温度センサーMADE IN TAIWANTemperature Sensor1M2

Comentarios a estos manuales

Sin comentarios