Futaba R6303SBE Manual de usuario descargar pdf

Usage condition for conventional system output

(Ch1-3) on "High Speed mode"

󾛽

CAUTION

󾛹

The "High Speed mode" accept the digital servos only or

most type of peripherals.

•Ifananalogservoisconnectedtotheseoutputsitwillcausea

malfunction.Pleasechecktheperipheralsifthereisamalfunctionfull

stickmovement.Ifthereisamalfunctionchangethereceiverbackto

"Normal mode."

Applicable systems: FASST-2.4GHz 7ch or 8ch/10ch/Multi-ch system

R6303SBE

Compliance Information Statement

(for U.S.A.)

This device, trade name Futaba Corporation of America, model number R6303SBE,

complies with part15 of the FCC Rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may

cause undesiredoperation.

The responsible party of this device compliance is:

Futaba Service Center

3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.

TEL (217)398-8970 or E-mail: [email protected] (Support)

R6303SBE Specications

FASST-2.4GHz (7ch/8ch/10ch/Multi-ch) system/S.BUS port and 3 channels for

conventional system/high-speed receiver

• Size: 0.89 x 1.47 x 0.37 in. (22.5 x 37.4 x 9.3 mm)

• Weight: 0.22 oz. (6.3g)

• Power requirement: 3.7V to 7.4V(Voltage range: 3.5 to 8.4V)

* Be sure that when using ESC's regulated output the capacity of the ESC must meet your usage

condition.

* The Battery F/S voltage is set for 4-cell NiCd/NiMH battery. Battery F/S function doesn't

work properly when other type battery is used.

* The fail safe function can be set for each channel when on "Multi-ch" mode, however, it differs

according to the transmitter. When on "7ch" mode, the fail safe function can be set for 3-channel

only.

* S.BUS port: R6303SBE can be used up to 7 channels or less on the "7ch" mode and 16 channels

+ DG1/2 or less on the "8ch/10ch/Multi-ch" mode, however, it differs according to the transmitter.

Thank you for purchasing a Futaba R6303SBE FASST-2.4GHz receiver.

The R6303SBE has an S.BUS system output port and 3 conventional

system channel outputs. It can also be used with conventional system

servos, etc. in addition to S.BUS system compatible servos and gyros,

etc. When the linking procedure is performed, R6303SBE recognizes the

signal mode (FASST-2.4GHz 7ch mode or 8ch/10ch/Multi-ch mode)

automatically.

The R6303SBE can change the output CH from seven groups (CH group

table).

In addition, the operating mode (high-speed mode/normal mode) can be

selected.

󾛽

WARNING

󾛻

DonotperformtheLinkingprocedurewiththe

motorpoweredup.Thiscouldresultinserious

injury.

󾛹

OncetheLinkingprocessiscompletedplease

cyclethepowertothereceivertomakesure

thatitislinkedandunderthecontrolofthetransmitter.

Link to the Transmitter

PressandholdtheLink/Modebuttonbetween2and5

seconds.

Re-adjust the 3CH F/S position (only for TM-8)

PressandholdtheLink/Modebuttonbetween1and2

seconds.

0 to 1 sec. 1 to 2 sec. 2 to 5 sec. More than 5 sec.

0 sec. 1 sec. 2 sec.

Press and Hold

No function

With TM-8

(not included in this set)

To set the F/S

position(No re-link)

Re-link(ID set) and to

set the F/S position

No function

Other than TM-8

(not included in this set)

Re-link(ID set)

CH change mode

5 sec.

Power Source Precautions

It is not recommended to use a power source of less then 4.0V.

However if less than 4.0V is used please keep in mind the conditions

below..

•The FailSafeFunctionMUSTbe set to"OFF"since itwilldisturb the

normal operation of the receiver.

•Please makesure that the fully loaded conditionontheESCand the

Servoswillnotdisturbnormal receiveroperation beforethe start of

youright.

 ThisisVERY Importantoncethe voltage dropsbelow3.5voltsthe

receiverwillnolongercontinuetooperate.

•Please be sure that everything on continues to work correctly all the

waydownto3.5volts.ie:Servos,ESC...

The input voltage must not exceed the servo rating or 8.4V which ever

is lower.

Link/Mode button

LED

R6303SBE

•Port2(InitialsettingistheChannel2)

•Port1(InitialsettingistheChannel1)

•Channel3outputforconventionalsystem/Battery

terminal

•S.BUSPort

(Connectors)

1M23N17464

FASST-2.4GHz (7ch/8ch/10ch/Multi-ch) S.BUS port and 3 channels for

conventional system High-Speed receiver

for parkﬂight or indoor use airplanes / small size electric helicopters.

󾛽

WARNING

󾛹

If a part of the fuselage is made of conductive

materials such as metal and carbon, install

the receiver so that it is never covered with these

materials and the antenna never touch them.

• It becomes impossibleto receive,it cases erratic operation or loss of

control.

󾛹

Do not use it for a middle or large scale model.

•R6203SBEforparkight orindooruseairplanes and small size

electrichelicoptersupto1000mmofmainrotordiameter.

Thereisapossibilityofcrashingwhenusingitforthemiddleorlarge

scale model.

1 2

Indice de contenidos

Pagina 1 - R6303SBE

Usage condition for conventional system output (Ch1-3) on "High Speed mode"󾛽CAUTION󾛹 The "High Speed mode" accept the digital serv

Pagina 2 - What is S.BUS?

Operation Normal/High Speed Mode SelectThe operation mode is set on "Normal mode" from the factory. To change the mode please follow the st

Comentarios a estos manuales

Sin comentarios

Futaba R6303SBE Manual de usuario

Busca en linea o descarga Manual de usuario para Accesorios de comunicación Futaba R6303SBE. Futaba R6303SBE User Manual [en] Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Accesorios de comunicación Futaba R6303SBE