Futaba R6203SBE Manual de usuario descargar pdf

Usage condition for conventional system

output (Ch1-3) on "High Speed mode"

󾛽

CAUTION

￸

The "High Speed mode" accept the digital servos

only or most type of peripherals.

s)FANYANALOGSERVOSCONNECTEDTOTHESEOUTPUTASIT

WILL CAUSEMALFUNCTION0LEASECHECK THEPERIPHERALSIF

THEREgS ANYMALFUNCTION WITH WHOLE STICK LEVERTHROW )F ANY

MALFUNCTIONOCCUR PLEASECHANGETHEOPERATIONMODETO

"Normal mode."

Applicable systems: FASST-2.4GHz 7ch or 8ch/10ch/Multi-ch system

Compliance Information Statement

(for U.S.A.)

This device, trade name Futaba Corporation of America, model

number R6203SB, complies with part15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including

interference that may cause undesiredoperation.

The responsible party of this device compliance is:

Futaba Service Center

3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.

TEL (217)398-8970 or E-mail: [email protected] (Support)



FASST-2.4GHz (7ch/8ch/10ch/Multi-ch) system/S.BUS port

and 3 channels for conventional system/high-speed receiver







        



* The Battery F/S voltage is set for 4-cell NiCd/NiMH battery. Battery F/S

function doesn't work properly when other type battery is used.



       



* S.BUS      

   



Usage precautions about the power source

We do not recommend to use the power source of less than

4.0V but if to use the lower voltage source please keep in

mind the condition shown below.

s&AIL3AFEFUNCTION-534BEINOFFSINCETHEBATTERYFSWILL

DISTURBTHENORMALOPERATION

s0LEASEMAKESURETHATTHEFULLLOADEDCONDITIONOFTHE%3#

AND THE SERVOS WONgT DISTURB THE RECEIVER OPERATION BEFORE

start ﬂight.

This is very important since the receiver will stop operation

WHENTHESUPPLYVOLTAGEDROPSTOLESSTHAN6

s0LEASE BE SURE THAT THE %3# OR SERVOS CAN KEEP mAWLESS

OPERATIONTILLSUCHALOWERVOLTAGE

The power source voltage must not exceed the servo's

rating.

󾛽

WARNING

￸

If a part of the fuselage is made of

conductive materials such as metal and

carbon, install the receiver so that it is never

covered with these materials and the antenna

never touch them.

s)T BECOMES IMPOSSIBLETO RECEIVEITCASES ERRATIC OPERATION

or loss of control.

￸

Do not use it for a middle or large scale

model.

s23"%FORPARKFLIGHTORINDOORUSEAIRPLANESAND

SMALLSIZE ELECTRIC HELICOPTERS UP TO MM OF MAIN ROTOR

diameter.

4HEREISAPOSSIBILITYOFCRASHINGWHENUSINGITFORTHEMIDDLE

or large scale model.

Link/Mode switch

LED

R6203SBE

s#HANNELOUTPUTFORCONVENTIONAL

system (2)

s#HANNELOUTPUTFORCONVENTIONAL

system (1)

s#HANNELOUTPUTFORCONVENTIONAL

system (3"ATTERYTERMINALB)

sS.BUS0ORTS.BUS)

#ONNECTORS

R6203SBE

FASST-2.4GHz (7ch/8ch/10ch/Multi-ch) System

S.BUS Port and 3 Channels for Conventional System

High-speed Receiver

For parkﬂight or indoor use airplanes.

For small size electric helicopters

Thank you for purchasing a Futaba R6203SBE F ASST-2.4GHz

compatible receiver.

The R6203SBE has an S.BUS system output port and a

conventional system channel outputs. It can also be used with

conventional system servos, etc. in addition to S.BUS system

compatible servos and gyros, etc.

When the linking procedure is performed, R6203SB

recognizes the signal mode (FASST-2.4GHz 7ch mode or

8ch/10ch/Multi-ch mode) automatically.

In addition, the operating mode (high-speed mode/normal

mode) can be selected.

-.

1 2

Indice de contenidos

Pagina 1 - R6203SBE

Usage condition for conventional system output (Ch1-3) on "High Speed mode"󾛽CAUTION￸ The "High Speed mode" accept the digital serv

Pagina 2 - Link to the transmitter

What is S.BUS?Different from conventional radio control systems the S.BUS system uses data communication to transmit control signals from a receiver t

Comentarios a estos manuales

Sin comentarios

Futaba R6203SBE Manual de usuario

Busca en linea o descarga Manual de usuario para Accesorios de comunicación Futaba R6203SBE. Futaba R6203SBE User Manual [es] Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Accesorios de comunicación Futaba R6203SBE