Usage condition for conventional system
output (Ch1-3) on "High Speed mode"
CAUTION
The "High Speed mode" accept the digital
servos only or most type of peripherals.
•Ifanyanalogservosconnectedtotheseoutputasit
willcausemalfunction.Pleasechecktheperipheralsif
there's anymalfunction with whole stick leverthrow. If any
malfunctionoccur pleasechangetheoperationmodeto
"Normal mode."
Applicable systems: FASST-2.4GHz 7ch or 8ch/10ch/Multi-ch system
R6203SB
FASST-2.4GHz (7ch/8ch/10ch/Multi-ch) System
S.BUS Port and 3 Channels for Conventional System
High-speed Receiver
Compliance Information Statement
(for U.S.A.)
This device, trade name Futaba Corporation of America, model
number R6203SB, complies with part15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesiredoperation.
The responsible party of this device compliance is:
Futaba Service Center
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.
R6203SB Specications
FASST-2.4GHz (7ch/8ch/10ch/Multi-ch) system/S.BUS port
and 3 channels for conventional system/high-speed receiver
• Dual antenna diversity
• Size: 0.89 x 1.47 x 0.37 in. (22.5 x 37.4 x 9.3 mm)
• Weight: 0.25 oz. (7.2g)
• Power requirement: 3.7V to 7.4V(Voltage range: 3.5 to 8.4V)
* Be sure that when using ESC's regulated output the capacity of the ESC
must meet your usage condition.
* The Battery F/S voltage is set for 4-cell NiCd/NiMH battery. Battery F/S
function doesn't work properly when other type battery is used.
* The fail safe function can be set for each channel when on "Multi-ch" mode,
however, it differs according to the transmitter. When on "7ch" mode, the
fail safe function can be set for 3-channel only.
* S.BUS port: R6203SB can be used up to 7 channels or less on the "7ch"
mode and 16 channels + DG1/2 or less on the "8ch/10ch/Multi-ch" mode,
however, it differs according to the transmitter.
Thank you for purchasing a Futaba R6203SB FASST-2.4GHz
compatible receiver.
The R6203SB has an S.BUS system output port and a
conventional system channel outputs. It can also be used with
conventional system servos, etc. in addition to S.BUS system
compatible servos and gyros, etc.
When the linking procedure is performed, R6203SB
recognizes the signal mode (FASST-2.4GHz 7ch mode or
8ch/10ch/Multi-ch mode) automatically.
In addition, the operating mode (high-speed mode/normal
mode) can be selected.
Usage precautions about the power source
We do not recommend to use the power source of less than
4.0V but if to use the lower voltage source please keep in
mind the condition shown below.
•FailSafefunctionMUSTbein"off"sincethebatteryf/swill
disturbthenormaloperation.
•PleasemakesurethatthefullloadedconditionoftheESC
and the servos won't disturb the receiver operation before
start flight.
This is very important since the receiver will stop operation
whenthesupplyvoltagedropstolessthan3.5V.
•Please be sure that the ESC or servos can keep awless
operationtillsuchalowervoltage.
The power source voltage must not exceed the servo's
rating.
Antenna installation precaution
WARNING
Besurethatthetwoantennasareplacedat90
degrees to each other.
•Futaba'sdual antenna diversity,or DAD, then seamlessly
selectsthebestsignalreceptionbetweentheseantennasto
ensurethatthereisnolossofsignal.
Antenna installation for carbon fuse
WARNING
Theantennaportionof30mmtipmustbefully
exposed.
•Pleasemakesurethattheexposedportionwon'tbeslided
backinthefusebythewindpressureorotherforceduring
the flight session.
(Antenna installation)
90˚
Link/Mode switch
LED
R6203SB
•Channel2outputforconventional
system (2)
•Channel1outputforconventional
system (1)
•Channel3outputforconventional
system (3)/Batteryterminal(B)
•S.BUSPort(S.BUS)
(Connectors)
(2 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales