Futaba R614FS Manual de usuario descargar pdf

Compliance Information Statement

(for U.S.A.)

This device, trade name Futaba Corporation of America, model number R614FS, complies with part15 of the FCC

Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

The responsible party of this device compliance is:

Futaba Service Center

3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.

TEL (217)398-8970 or E-mail: [email protected] (Support)

FUTABA CORPORATION

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan

Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

©FUTABA CORPORATION 2011, 8 (1)

R614FS Speciﬁcations:

(

FASST

system, 4-channel receiver)

•Receivingon2.4GHzband

•System:

FASST-C2

system

AtNormal/Highspeedmode(autodetection)

•

PowerrequirementRatedvoltage:3.7V-7.4V/Usablevoltage:3.5-8.4V

• F/SandBatteryF/Sfunction:Itissetaccordingtothetransmitterused.

• BatteryF/Svoltage:Setitwiththetransmitterarbitrarily.

•Size:1.38x0.91x0.33”(35.1x23.2x8.5mm)

•Weight:0.28oz.(8g)

󾛽

WARNING

󾛻

NEVERusedrybatteriesforthe

powersupplyoftheR614FS as this

maycausedifcultieswiththereceiver's

operation.

󾛹

Wrapthereceiverwithsomething

soft,suchasfoamrubber,toavoid

vibration.Donotsplashwateroverthe

receiver.

󾛹

Sincethereceivergeneratesa

certainamountofheat,installthe

placewithgoodventilation.

Link Procedure

Each transmitter has an individually assigned,

unique ID code. In order to start operation, the

receiver must be linked with the ID code of the

transmitter with which it is being paired. Once the

link is made, the ID code is stored in the receiver

and no further linking is necessary unless the

receiver is to be used with another transmitter.

Placethetransmitterandthereceiverclose

toeachotherwithinhalf(0.5)meter.

Turnonthetransmitterandthereceiver.

PushandholdtheLinkswitchonthe

receiver.

Whenthelinkiscomplete,theLEDonthe

receiverchangestosolidgreen.

*Pleaserefer to the table belowfor LED status

andreceivercondition.

Nosignalreception LED:Red

Receivingsignals LED:Green

Receivingsignals,butID

isunmatched.

LED:GreenBlink

Unrecoverablefailure

(EEPROM,etc.)

LED:RedandGreen

turnonalternately

*Iftherearemany

FASST

systemsturnedon

aroundyourreceiver,itmightnotlinktoyour

transmitter. In thiscase, even ifthereceiver’s

LEDstayssolidgreen,unfortunatelythe

receivermighthaveestablishedalinktooneof

the other transmitters. This is very dangerous

ifyou donotnotice this situation.  In order to

avoidtheproblem,westronglyrecommend

you todouble-checkwhetheryour receiver is

controlled by your transmitter bygiving throttle

input,etc.andthencheckingservoresponse.

󾛽

WARNING

󾛹

Afterthelinkingisdone,pleasecycle

receiverpowerandcheckifthereceiver

tobelinkedisreallyunderthecontrolbythe

transmittertobelinked.

󾛻

Donotperformthelinkingprocedure

withmotor'smainwireconnectedor

withtheengineoperatingasitmayresultin

seriousinjury.

Link switchLED

Battery / DSC

terminal (B/C)

CH output (1 to 4)

Operating Precautions:

Oncethe

R614FS

detectsthe

FASST

normalmodeor

FASST

highspeed

mode,thedetectedmodeislocked

aslongasthe powerisON.When

needtochangethemode,please

cyclepower.

Note:

The R614FS is compatible with the FASST-C2 system

transmitters (Futaba T4PK/T4PKS).

The receiver type setting of the transmitter is set in FASST-C2.

*Futaba FASST system does not work with current Futaba S-FHSS/FHSS system.

Usage condition on "High Speed mode"

󾛽

CAUTION

󾛹

Whenusingthehigh-speedmode,useaFutaba

digitalservo(includingbrushlessservo).Analog

servoscannotbeused.

•Theuseofanalogservosmaycauseservotrouble.

1M23N17448

FASST-2.4GHz System

Diversity 4-Channel

Receiver for Model Car

Thank you for purchasing the

R614FS

receiver.

The

R614FS

is designed for use with the Futaba

FASST-C2

system transmitter. The

FASST

system has

two(2) operation mode as shown below.

•Normal mode/High Speed mode

The "Normal mode" accepts any type of servos

or the peripheral. The "High Speed mode" only

accepts the digital servos, including BLS series, and

most peripheral equipments such as the brushless

ESCs. However, there is a transmitter that cannot

correspond, too.

Please pay special attention to the information

contained within this manual and transmitter's manual

in order to have a pleasant running/ying experience.

The

R614FS

is compatible with the

FASST-C2

system

transmitters.

The

R614FS

is equipped with the diversity antenna.

The

R614FS

selects either the outer antenna or the

inner antenna which has better reception of signal.

R614FS

Indice de contenidos

Pagina 1 - CH output (1 to 4)

Compliance Information Statement (for U.S.A.)This device, trade name Futaba Corporation of America, model number R614FS, complies with part15 of the F

Comentarios a estos manuales

Sin comentarios

Futaba R614FS Manual de usuario

Busca en linea o descarga Manual de usuario para Accesorios de comunicación Futaba R614FS. Futaba R614FS User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Accesorios de comunicación Futaba R614FS