Futaba R614FF-E Manual de usuario descargar pdf

Compliance Information Statement

(for U.S.A.)

This device, trade name Futaba Corporation of America, model number R614FF-E, complies with part15 of the

FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

The responsible party of this device compliance is:

Futaba Service Center

3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.

TEL (217)398-8970 or E-mail: [email protected] (Support)

FUTABA CORPORATION

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan

Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

R614FF-E Speciﬁcations:

(

FASST

system, 4-channel receiver)

•Receivingon2.4GHzband

•System:

FASST-C2

system

AtNormal/Highspeedmode(autodetection)

•

ReceivingRange:70m(230ft.)(atthebestconditions)

•

PowerrequirementRatedvoltage:3.7V-7.4V/Usablevoltage:3.5-8.4V

• F/SandBatteryF/Sfunction:Itissetaccordingtothetransmitterused.

• BatteryF/Svoltage:Setitwiththetransmitterarbitrarily.

•Size:1.38x0.91x0.35”(35.1x23.2x9.0mm)

•Weight:0.27oz.(7.6g)

󾛽

WARNING

󾛻

NEVERusedrybatteriesforthe

powersupplyoftheR614FF-E as this

maycausedifcultieswiththereceiver's

operation.

󾛻

NEVERusetheR614FF-EinGP

cars.

󾛹

Wrapthereceiverwithsomething

soft,suchasfoamrubber,toavoid

vibration.Donotsplashwateroverthe

receiver.

󾛹

Sincethereceivergeneratesa

certainamountofheat,installthe

placewithgoodventilation.

Link Procedure

Each transmitter has an individually assigned,

unique ID code. In order to start operation, the

receiver must be linked with the ID code of

the transmitter with which it is being paired.

Once the link is made, the ID code is stored in

the receiver and no further linking is necessary

unless the receiver is to be used with another

transmitter.

Placethetransmitterandthereceiver

closetoeachotherwithinhalf(0.5)meter.

Turnonthetransmitterandthereceiver.

PushandholdtheLinkswitchonthe

receiver.

Whenthelinkiscomplete,theLEDonthe

receiverchangestosolidgreen.

*PleaserefertothetablebelowforLEDstatus

andreceivercondition.

Nosignalreception LED:Red

Receivingsignals LED:Green

Receivingsignals,butID

isunmatched.

LED:GreenBlink

Unrecoverablefailure

(EEPROM,etc.)

LED:RedandGreen

turnonalternately

*Ifthere aremany

FASST

 systemsturnedon

aroundyourreceiver,itmight notlinkto your

transmitter.Inthiscase,evenifthereceiver’s

LEDstayssolidgreen,unfortunatelythe

receivermighthaveestablishedalinkto

oneoftheother transmitters.This isvery

dangerous if you do not notice this situation.

In ordertoavoidthe problem,westrongly

recommendyoutodouble-checkwhether

yourreceiveriscontrolledbyyourtransmitter

bygivingthrottleinput,etc.andthenchecking

servoresponse.

󾛽

WARNING

󾛹

Afterthelinkingisdone,please

cyclereceiverpowerandcheckif

thereceivertobelinkedisreallyunder

thecontrolbythetransmittertobe

linked.

󾛻

Donotperformthelinking

procedurewithmotor'smainwire

connectedorwiththeengineoperating

asitmayresultinseriousinjury.

Link switchLED

Battery / DSC

terminal (B/C)

CH output (1 to 4)

Operating Precautions:

Once the

R614FF-E

detectsthe

FASST

normalmodeor

FASST

high

speedmode,thedetectedmodeis

lockedaslongasthepowerisON.

Whenneedtochange themode,

pleasecyclepower.

Note:

The R614FF-E is compatible with the FASST-C2 system

transmitters (Futaba T4PK/T4PKS).

*Futaba FASST system does not work with current Futaba S-FHSS/FHSS system.

Usage condition on "High Speed mode"

󾛽

CAUTION

󾛹

Whenusingthehigh-speedmode,useaFutaba

digitalservo(includingbrushlessservo).Analog

servoscannotbeused.

•Theuseofanalogservosmaycauseservotrouble.

FASST-2.4GHz System

Built-in Antenna

4-Channel Receiver

for EP Car Models

Thank you for purchasing the

R614FF-E

receiver.

The

R614FF-E

is designed for use with the Futaba

FASST-C2

system transmitter. The

FASST

system has

two(2) operation mode as shown below.

•Normal mode/High Speed mode

The "Normal mode" accepts any type of servos or

the peripheral equipment. The "High Speed mode"

only accepts the digital servos, including BLS series,

and most peripheral equipment such as the brushless

ESCs. However, there is a transmitter that cannot

correspond, to high speed mode.

Please pay special attention to the information

contained within this manual and transmitter's manual

in order to have a pleasant running experience.

•Built-in antenna

The

R614FF-E

receiver is designed to be used only for

EP Car models.

The R614FF-E is compatible with the

FASST-C2 system transmitters.

R614FF-E

1M23N17457

R614FF-E 1

Indice de contenidos

Pagina 1 - R614FF-E

Compliance Information Statement (for U.S.A.)This device, trade name Futaba Corporation of America, model number R614FF-E, complies with part15 of the

Comentarios a estos manuales

Sin comentarios

Futaba R614FF-E Manual de usuario

Busca en linea o descarga Manual de usuario para Accesorios de comunicación Futaba R614FF-E. Futaba R614FF-E User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Accesorios de comunicación Futaba R614FF-E