Futaba R2104GF Manual de usuario

Busca en linea o descarga Manual de usuario para Accesorios de comunicación Futaba R2104GF. Futaba R2104GF User Manual Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 1
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 0
R2104GF
S-FHSS/FHSS-2.4GHz system
(Auto Detection),
4-channel receiver
Compliance Information Statement
(for U.S.A.)
This device, trade name Futaba Corporation of America, model number R2104GF, complies
with part15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesiredoperation.
The responsible party of this device compliance is:
Futaba Service Center
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.
TEL (217)398-8970 or E-mail: [email protected] (Support)
Thank you for purchasing the
R2104GF
receiver.
The
R2104GF
is designed for use with the Futaba
S-FHSS
or
FHSS
system transmitter. The
S-FHSS
system has two(2) operation mode as shown below.
•Normal mode/High Speed mode
The "Normal mode" accepts any type of servos
or the peripherals as the frame rate of the output
is 13.6ms. The "High Speed mode" only accepts
the digital servos, including BLS series, and most
peripheral equipments such as the brushless ESCs.
The frame rate of the outputs is 6.8ms.
Please pay special attention to the information
contained within this manual and transmitter's
manual in order to have a pleasant running/ying
experience.
The
R2104GF
is compatible with the
S-FHSS
or
FHSS
system transmitters as shown "Transmitter
and Receiver Compatibility".
FUTABA CORPORATION
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan
Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
1M23N17432 ©FUTABA CORPORATION 2010, 8 (1)
R2104GF Specications:
(
S-FHSS/FHSS
system, 4-channel receiver)
•Receivingon2.4GHzband
•System:
S-FHSS/FHSS
system(autodetection)
•Operationmode:Normal/Highspeed(autodetection)
•Powerrequirement:4.8Vor6V(sharedwithservo)
•Currentdrain:30mA(atnosignal)
•Size:1.54x1.02x0.39”(39x26x10mm)
•Weight:0.28oz.(8g)
󾙏
WARNING
󾙍
NEVER use drybatteries for
thepowersupplyoftheR2104GF
astheymaycausedifculties.
Link Procedure
Each transmitter has an individually assigned,
unique ID code. In order to start operation, the
receiver must be linked with the ID code of the
transmitter with which it is being paired. Once the
link is made, the ID code is stored in the receiver
and no further linking is necessary unless the
receiver is to be used with another transmitter.
1
Placethetransmitterandthereceiverclose
toeachotherwithinone(1)meter
2
Turnonthetransmitterandthereceiver.
3
Push and hold the Link switch on the
receiver.
4
Whenthelinkiscomplete,theLEDonthe
receiverchangestosolidgreen.
*Please referto the table below for LED status
andreceivercondition.
Nosignalreception Red:On
Receivingsignals Green:On
Receivingsignals,butID
isunmatched.
Green:Blink
*If there are many
S-FHSS/FHSS
systems turned
onaroundyourreceiver,itmightnotlinktoyour
transmitter. In this case, even if the receiver’s
LED stays solid green, unfor tunately the
receivermighthaveestablishedalinktooneof
the other transmitters. This is very dangerous
if you do not notice this situation. In order to
avoid the problem, we strongly recommend
you to double-check whether your receiver is
controlled byyour transmitter by giving throttle
input,etc.andthencheckingservoresponse.
󾙏
WARNING
󾙋
After the linking is done, please
cycle receiver power and check if
the receiverto belinkedisreally underthe
controlbythetransmittertobelinked.
󾙍
Do notperformthe linking procedure
with motor'smain wire connectedor
withtheengineoperatingasitmayresultin
seriousinjury.
FHSS-2.4GHz/S-FHSS-2.4GHz System
Transmitter and Receiver Compatibility
Transmitter
FHSS
Receiver
S-FHSS/FHSS
Receiver
R603GF
R2004GF
R2104GF
T2PL-2.4G (FHSS) Okay Okay
F/Sfunction:Ch2
T3PL-2.4G (FHSS) Okay Okay
F/Sfunction:Ch2
T4YF-2.4G (FHSS) Okay Okay
T4PL-2.4G
S-FHSS
High Speed
Okay
F/Sfunction:Allchannels
B-F/Sfunction:Ch2
*DigitalservoonlyatHighSpeed
mode
Normal
FHSS Okay Okay
F/Sfunction:Ch2
Link switch LED
Ch output (1 to 4)
Battery terminal (B)
Operating Precautions:
Oncethe
R2104GF
detectsthe
S-FHSS
normalmode,
S-FHSS
high speed
modeor
FHSS
mode, the detected
modeislockedaslongasthepower
is ON.When need to change the
mode,pleasecyclepower.
Note:Futaba
FHSS/S-FHSS
systemand
FASST
systemarenotcompatibleeachother.
Usage condition on "High Speed mode"
󾙏
CAUTION
󾙋
When using the high-speed mode, use a
Futaba digital servo (including brushless
servo).Analogservoscannotbeused.
•Theuseofanalogservosmaycauseservotrouble.
Vista de pagina 0
1

Indice de contenidos

Pagina 1 - Link Procedure

R2104GFS-FHSS/FHSS-2.4GHz system(Auto Detection),4-channel receiverCompliance Information Statement (for U.S.A.)This device, trade name Futaba Corpora

Comentarios a estos manuales

Sin comentarios