Futaba R204GF-E Manual de usuario

Busca en linea o descarga Manual de usuario para Accesorios de comunicación Futaba R204GF-E. Futaba R204GF-E User Manual Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 1
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 0
Compliance Information Statement
(for U.S.A.)
This device, trade name Futaba Corporation of America, model number R204GF-E, complies with part15 of the FCC
Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesiredoperation.
The responsible party of this device compliance is:
Futaba Service Center
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.
TEL (217)398-8970 or E-mail: [email protected] (Support)
FUTABA CORPORATION
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan
Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
©FUTABA CORPORATION 2011, 11 (1)
R204GF-E Specifications:
(
S-FHSS/FHSS
system, 4-channel receiver)
•Receivingon2.4GHzband
•System:
S-FHSS/FHSS
system(autodetection)
At
S-FHSS
Normal/Highspeedmode(autodetection)
ReceivingRange:70m(230ft.)(atthebestconditions)
•
Operatingvoltage(Typ.):4.8V-7.4V(
sharedwithservo)
• F/SandBatteryF/Sfunction:Theoperationchannelsdifferaccordingtothetransmitterused.However,Battery
F/Sdoesn'tfunctionwhenitisusedwithFHSSandF/SbecomesonlyCH2.
• BatteryF/Svoltage:3.8V
•Currentdrain:30mA(atnosignal)
•Size:1.38x0.91x0.35”(35.1x23.2x9mm)
•Weight:0.21oz.(6g)
*
The Battery F/S voltage is set for 4-cell NiCd/NiMH battery. Battery F/S function doesn't work
properly when other type battery is used.
󾛽
WARNING
󾛻
NEVERusedrybatteriesforthe
powersupplyoftheR204GF-E as
theymaycausedifculties.
󾛻
NEVER use the R204GF-EinGP
cars.
Link Procedure
Each transmitter has an individually assigned,
unique ID code. In order to start operation, the
receiver must be linked with the ID code of the
transmitter with which it is being paired. Once the
link is made, the ID code is stored in the receiver
and no further linking is necessary unless the
receiver is to be used with another transmitter.
1
Placethetransmitterandthereceiverclose
toeachotherwithinhalf(0.5)meter
2
Turnonthetransmitterandthereceiver.
3
PushandholdtheLinkswitchonthe
receiver.
4
Whenthelinkiscomplete,theLEDonthe
receiverchangestosolidgreen.
*Pleaserefer to the table belowfor LED status
andreceivercondition.
Nosignalreception LED:Off
Receivingsignals LED:On
Receivingsignals,butID
isunmatched.
LED:Blink
PowerOn,whenF/S
setsit.
LED:Early
Blinktherst
onesecond
*Ifthere are many
S-FHSS/FHSS
systems turned
onaroundyourreceiver,itmightnotlinktoyour
transmitter. In thiscase, even ifthereceiver’s
LEDstayssolidgreen,unfortunatelythe
receivermighthaveestablishedalinktooneof
the other transmitters. This is very dangerous
ifyou donotnotice this situation. In order to
avoidtheproblem,westronglyrecommend
you todouble-checkwhetheryour receiver is
controlled by your transmitter bygiving throttle
input,etc.andthencheckingservoresponse.
󾛽
WARNING
󾛹
Afterthelinkingisdone,pleasecycle
receiverpowerandcheckifthereceiver
tobelinkedisreallyunderthecontrolbythe
transmittertobelinked.
󾛻
Donotperformthelinkingprocedure
withmotor'smainwireconnectedor
withtheengineoperatingasitmayresultin
seriousinjury.
Link switchLED
Ch4 output/Battery terminal (B)
Ch output (1 to 3)
Operating Precautions:
Once the
R204GF-E
detectsthe
S-FHSS
normalmode,
S-FHSS
high
speedmodeor
FHSS
mode,the
detectedmodeislockedaslong
asthepowerisON.Whenneed
tochangethemode,please cycle
power.
Note:
The R204GF-E is compatible with the S-FHSS or FHSS
system transmitters .
*Futaba S-FHSS/FHSS system does not work with current Futaba FASST system.
Usage condition on "High Speed mode"
󾛽
CAUTION
󾛹
Whenusingthehigh-speedmode,useaFutaba
digitalservo(includingbrushlessservo).Analog
servoscannotbeused.
•Theuseofanalogservosmaycauseservotrouble.
1M23N17456
S-FHSS/FHSS-2.4GHz
system
(Auto Detection),
For EP Car models
Built-in antenna
4-channel receiver
Thank you for purchasing the
R204GF-E
receiver.
The
R204GF-E
is designed for use with the Futaba
S-FHSS
or
FHSS
system transmitter. The
S-FHSS
system has two(2) operation mode as shown below.
•Normal mode/High Speed mode
The "Normal mode" accepts any type of servos or the
peripherals as the frame rate of the output is 13.6ms.
The "High Speed mode" only accepts the digital
servos, including BLS series, and most peripheral
equipments such as the brushless ESCs. The frame rate
of the outputs is 6.8ms. However, there is a transmitter
that cannot correspond, to high speed mode.
Please pay special attention to the information
contained within this manual and transmitter's manual
in order to have a pleasant running experience.
•Built-in antenna
The
R204GF-E
receiver is designed to be used only
for EP Car models. Due to the special design of the
R204GF-E
, we cannot recommend its use in other
types of models (gas poweredmodels.)
•The R204GF-E is compatible with the
S-FHSS or FHSS system transmitters.
R204GF-E
Vista de pagina 0
1

Indice de contenidos

Pagina 1 - R204GF-E

Compliance Information Statement (for U.S.A.)This device, trade name Futaba Corporation of America, model number R204GF-E, complies with part15 of the

Comentarios a estos manuales

Sin comentarios