R2004GF
FHSS-2.4GHz system,
4-channel receiver
Compliance Information Statement
(for U.S.A.)
This device, trade name Futaba Corporation of America, model number R2004GF, complies
with part15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesiredoperation.
The responsible party of this device compliance is:
Futaba Service Center
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.
Thank you for purchasing the
R2004GF
receiver. This receiver is designed for use
with the Futaba
FHSS
system transmitter.
P l e a s e p a y s pe c i a l at t e n t i o n to t he
information contained within this manual
and transmitter's manual in order to have
a pleasant running/flying experience. The
R2004GF
is compatible with the FHSS
system transmitters as shown "Transmitter
and Receiver Compatibility".
FUTABA CORPORATION
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan
Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
1M23N17436 ©FUTABA CORPORATION 2010, 8 (1)
R2004GF Specifications:
(
FHSS
system, 4-channel receiver)
•Receivingon2.4GHzband
•Powerrequirement:4.8Vor6V
(sharedwithservo)
•Currentdrain:30mA(atnosignal)
•Size:1.54x1.02x0.39”(39x26x10mm)
•Weight:0.28oz.(8g)
WARNING
NEVER
usedrybatteriesforthe
powersupplyofthe
R2004GF
as
theymaycausedifculties.
Link Procedure
Eac h trans m i tter has a n in d i v idually
assigned, unique ID code. In order to start
operation, the receiver must be linked
with the ID code of the transmitter with
which it is being paired. Once the link is
made, the ID code is stored in the receiver
and no further linking is necessary unless
the receiver is to be used with another
transmitter.
1
Placethetransmitterandthereceiver
close to each other within one (1)
meter
2
Tur n on the transmitter and the
receiver.
3
PushandholdtheLinkswitchonthe
receiver.
4
When the link is complete, the LED
on the receiver changes to solid
green.
*Please refer to the table below for LED
statusandreceivercondition.
Nosignalreception Red:On
Receivingsignals Green:On
Receivingsignals,butID
isunmatched.
Green:Blink
*If there are many
FHSS
systems turned
onaroundyourreceiver,itmightnotlink
to your transmitter. In this case, even
if the receiver’sLED stays solid green,
unfortunately the receiver might have
established a link to one of the other
transmitters. This is very dangerous
if you do not notice this situation. In
order to avoid the problem, we strongly
recommendyoutodouble-checkwhether
you r re cei ver is controlled by you r
transmitter by giving throttle input, etc.
andthencheckingservoresponse.
WARNING
Afterthelinkingisdone,please
cyclereceiverpowerandcheckif
thereceivertobelinkedisreally
underthecontrol bythetransmitter
tobelinked.
Donotperformthelinking
procedurewithmotor'smainwire
connectedorwiththe engine
operatingasitmayresultinserious
injury.
FHSS-2.4GHz/S-FHSS-2.4GHz System
Transmitter and Receiver Compatibility
Transmitter
FHSS
Receiver
S-FHSS/FHSS
Receiver
R603GF
R2004GF
R2104GF
T2PL-2.4G (FHSS) Okay Okay
F/Sfunction:Ch2
T3PL-2.4G (FHSS) Okay Okay
F/Sfunction:Ch2
T4YF-2.4G (FHSS) Okay Okay
T4PL-2.4G
S-FHSS
High Speed
— Okay
F/Sfunction:Allchannels
B-F/Sfunction:Ch2
*DigitalservoonlyatHighSpeed
mode
Normal
FHSS Okay Okay
F/Sfunction:Ch2
NOTE:Futaba
FHSS/S-FHSS
systemand
FASST
system are
notcompatibleeachother.
Link switch LED
Ch output (1 to 4)
Battery terminal (B)
(2 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales