Futaba 7UAF, 7UAP Manual de usuario

FutabaDIGITAL PROPORTIONALRADIO CONTROLFP-7UAPPCM 1024 SYSTEMFP-7UAFFM SYSTEMD60460

• FUNCTION AND DATA SETTINGSet for a different CH anddirection by repeating stepstoSet the rate with thekeys. (When the + and— keys are pressed simul

• FUNCTION AND DATA SETTINGTo REVTo F/SFunctionDisplayData settingCH selectionSelect the CH to which EXP isto be applied with thekeys.EXPEXPONENTIALTh

• FUNCTION AND DATA SETTINGPress the [MODE SELECT]To normal display modeCH selectionSelect the CH which is to beset to F/S or HOLD with thekeys. (CH N

• FUNCTION AND DATA SETTINGPress the [MODE SELECT]To normal display modeMixing activate/inhibit mode settingSet the mode with thekeys.+ : Activate—: I

• FUNCTION AND DATA SETTINGPress the [MODE SELECT]To normal display modeMixing activate/inhibit mode settingSet the mode with thekeys.+ : Activate-:

• FUNCTION AND DATA SETTINGPressthe [MODE SELECT]To normal display mode2-6ELEVATOR ->> FLAP MIXINGMixing activate/inhibit mode settingSet the m

• FUNCTION AND DATA SETTINGPress the [MODE SELECT]To normal display modeActivate/inhibit mode settingSet the mode with thekeys.+ : Activate-: Inhibit

• FUNCTION AND DATA SETTINGPress the [MODE SELECT]To normal display modeActivate/inhibit mode settingSet the mode with thekeys.+ : Activate-: InhibitS

• FUNCTION AND DATA SETTINGPressthe (MODE SELECT]keys simultaneouslyTo normal display modeActivate/inhibit mode settingSet the mode with thekeys.+ :

• FUNCTION AND DATA SETTINGPress the [MODE SELECT]To normal display modeActivate/inhibit mode settingSet the mode with thekeys.+ : Activate-: InhibitS

Thank you for purchasinga Futaba digital proportional radio control set.Please read this manualcarefully before using your setThe last page of this ma

• FUNCTION AND DATA SETTINGPress the. [MODE SELECT]To normal display modeFLTRFLAP TRIMFLAP TRIM (CH6) lever operation<-> normal operation switc

• FUNCTION AND DATA SETTING• OTHER FUNCTIONSPress the [MODE SELECT]To normal display modeMode selectionMODMODULATIONThe modulation can be switchedPCM

• OTHER FUNCTIONS• USING THE ACCESSORIES• Trainer function (Trainer cable optional)2 Operating at the instructor sideOperation is possible by turning

• USING THE ACCESSORIES• Digital Proportional Frequencies (FOR U.S.A.)• The frequency of Futaba digital proportional sets can be changed within their

• NOMENCLATUREElevator trim lever... (MODE II)Throttle trim lever... (MODE I)Power switchThrottle trim lever... (MODE II)Elevator trim lever...

• SERVO EXPLODED VIEWFP-S148 FP-S3001No.1234567891011121314151617181920212223Part NameUpper caseMiddle caseBottom caseMetal bearing innerMetal bearing

Printed in Japan/900330CC

• TABLE OF CONTENTSSET CONTENTS ...2BEFORE USING ...3-5DISPLAY FUNCT

• SET CONTENTS*Specifications are subject to change without prior notice.FP-7UAPFP-7UAFRating• FP-T7UAP (X1)• FP-T7UAF (X1)2 sticks, 7 channels, PCM o

• BEFORE USING• Charging the transmitter and receiver Nicd battery*Use the special Futaba charger.• The charging time is 15 hours.[However when the b

• BEFORE USING• RECEIVER AND SERVO CONNECTIONSPay careful attention to thepolarity of the connector.CH7 (AUX)CH6 Flap servoCH5Landing gearservoOption

• BEFORE USINGdrain the battery pack very quickly. Make thetravel of each control mechanism somewhatlarger than the full stroke (including trim)

• DISPLAY FUNCTION• Used in display mode switching.• Used in setting function selection• Used at data setting.Liquid crystal panel• Operated in thr

• DISPLAY FUNCTIONmode switchingThe display mode isswitched by pres-sinq thekeys simul-taneously.(Set function recall)• The function is selected byI