Futaba 6EX 2.4GHz Manual de usuario

6EX-2. 4GHzINSTRUCTION MANUALfor Futaba 6EX-2.4GHz6-channel, FASSTRadio control systemfor Airplanes/Helicopters1M23N12014Futaba CorporationTechnical u

10RECEIVER AND SERVO CONNECTIONS Connect the servos to the receiver to perform the functions indicated:Receiver output channelFunctionAircraft (ACRO)

11CHARGING THE NiCd BATTERIESThe transmitter batteries included with your 6EX-2.4GHz system are rechargeable, NiCd (nickel-cadmium, pronounced ni-kad)

12LIQUID CHIP DISPLAY (LCD) & PROGRAMMING CONTROLSTo open programming menu; Press both keys simultaneously and hold for one second MODE key -

13Transmitter battery voltage “Battery” icon In addition to the model type, the LCD screen also displays the transmitter battery voltage. When the vol

14PROGRAMMING THE 6EX-2.4GHz RADIO Anytime you wish to view or change any of the current settings in the transmitter, the programming mode must first

15ACRO/HELI Model type select functionThe Model type select function is used to select the ACRO or HELI mode of model type.ACRO: Powered aircraft memo

16Model name functionAssign a name to the model memory. By giving each model a name that is immediately recognizable, you can quickly select the corre

17the throw. 5. Repeat the procedure for the other dual rate (channel 2-elevator, 4-rudder). EXPO Exponential Settings The “exponentials” are in the

18TRIM Trim SettingsThere are four trim levers (“trims”) on the front of the transmitter. Three of the trims are for adjusting the neutral position

19PMIX1/2 Programmable Mixer 1/2 (ACRO only)Unlike the “wing mixing” function (explained later) where the channels to be mixed are factory-set, the

2TABLE OF CONTENTSIntroduction ...3Service ...

20Wing Mixing Type Selection (ACRO only)With the programmable mix (previously described) the user determines the two channels to be mixed. The wing mi

21To activate flap trim: 1. Enter the programming mode. Access the “FLTR” screen with the MODE key. 2. If “INH” is blinking, push DATA INPUT lever upwa

224. Next you may set the elevator. Press the SELECT key to display the “CH2” and flashing “%” sign. Use the DATA INPUT lever to set the percentage of

233. Push the DATA INPUT lever upward for 0.5 seconds. This will cause the flashing “INH” display to change to a flashing “ON” display. Now the mixing

24N-TH Normal throttle curve function (HELI only)Used to set throttle curve for normal flight. 5-point throttle curve is utilized to best match the b

253. Use SELECT key to select the desired curve point. Point 1 is shown initially which is throttle stick’s all the way downward (slow) position. Poin

26REVO Pitch-rudder mixing function (HELI only)This mix adds rudder in conjunction with pitch. This helps compensate for rotation of the helicopter

27specialized digital servos. Examples: • GY401: Simpler set up. Ideal for learning aerobatics through 3D. • GY502: Better centering than 401 for mo

28SW-T Swash to throttle mixing (HELI only)This function corrects slowing of engine speed caused by swashplate operation at aileron or elevator oper

29To select the swashplate types:1. Enter the programming mode and use the MODE key to access the “SWSH” function.2. To select swashplate type press t

3INTRODUCTIONThank you for purchasing the Futaba 6EX-2.4GHz FASST*1 digital proportional R/C airplane/helicopter system. If this is your first “compute

30F/S Fail Safe (Throttle channel <ch 3> only)The Fail Safe function is recommended to use for safety reasons in the event of radio interference

31MODE keyMODE keySELECT keyDATA INPUTlever[CH 2-5][CH 2-5][CH 2-3][Model 2-5](press MODE and SELECT keys for one second)*1. Press the DATA INPUT leve

32Stick Mode MODE key MODE key SELECT key DATA INPUT lever [CH 2-5] [CH 2-5] [CH 2-3] [2-4] [2-4] [2-4] [2-4] [Model 2-5] (press MODE and SELECT keys

33OTHER 6EX-2.4GHz FUNCTIONSTrainer switch (ACRO mode)To utilize the trainer function, the appropriate trainer cord (available separately) and a secon

34Adjustable-length control sticks The control stick length is adjustable to make the transmitter more comfortable to hold and operate. To adjust the

35FLIGHT PREPARATIONFlight preparation is to be done at the flying field.If you are an inexperienced pilot, be certain your flight instructor performs th

MENU FUNCTIONREVR Servo ReverseD/R Dual Rate settingEPA End Point AdjustTRIM TrimsEXPO Exponential settingF/S FailsafeCH 1 CH 2 CH 3 CH 4 CH 5 CH 6N

MODEL DATA RECORDING SHEET (HELI) (Make copies before using)Model name: Model No. 1• 2 • 3 • 4 • 5 • 6Model Type: HELI MENU FUNCTION REVR Servo Rev

38FUTABA CORPORATIONMakuhari Techno Garden Bldg., B6F 1-3 Nakase, Mihama-ku, Chiba 261-8555, JapanPhone: (043) 296-5119 Facsimile: (043) 296-5124©FUT

4Transmitter: T6EX-2.4GT6EX-2.4GHz Transmitter of FASST system.Transmitting on 2.4GHz band.Operating system: 2-stick, 6-channel systemPower supply: 9.

5INTRODUCTION TO THE 6EX-2.4GHz SYSTEMIMPORTANT!: Always turn on the transmitter first, then the receiver. When turning off the system, always turn off

6Trim levers (all) - Used to shift the neutral or center position of each servo as labeled in the diagram. Once either trim lever is operated, the tri

7RADIO INSTALLATIONFollow these guidelines to properly mount the servos, receiver and battery. • Make certain the alignment tab on the battery, switc

8• IMPORTANT: Since the 2.4GHz have different characteristics than that of the conventional 27MHz and 72MHz frequencies, please read this section car

9Transmitter Antenna1. The transmitter antenna is adjustable so please make sure that the antenna is never pointed directly at the model when flying as