Futaba
DIGITAL PROPORTIONAL
RADIO CONTROL
FP-2GS
D60431
SPECIAL FEATURES:
SET CONTENTS AND RATINGS
(Specifications are subject to change without prior notice.)
TRANSMITTER FP-T2GS
• Contemporary
styling with smooth operating gimbals for
superior control.
• 500mW output.
• Battery level
meter indicates the state of the battery
voltage at a glance.
• Built-in antenna.
RECEIVER FP-R102GF
•BEC (Battery Eliminator Circuitry) system allows sharing
of the running Nicd battery and eliminates the need
for a
regulator and diode.
•High performance 2 channel receiver with ASP system
when used with the proper transmitter.
•Crystal
socket
uses
a
new
type
of highly reliable subminia-
ture pins. Reliability is increased and the crystal can be
changed from the outside.
SERVO FP-S128
SMALL, RUGGED. HIGH NEUTRAL SERVO
•Skew type armature motor.
Movement of the trimmer by even one notch is tracked by
a skew type motor which displays a performance near that
of a
coreless motor.
•New indirect drive potentiometer improves vibration and
shock resistance and neutral accuracy.
•Futaba low-power custom 1C provides extremely high
torque, narrow dead band, and superior tracking.
•Fiberglass reinforced PBT (polybutylene terephthalate)
injection
molded
servo
case
is
mechanically strong and
invulnerable to glow fuel.
•Strong
polyacetal
resin
ultra-precision
servo
gear
features
smooth operation, positive neutral, and very little backlash.
•Fiberglass reinforced epoxy resin PC board with thru-the-
hole plating improves servo amp vibration and shock resist-
ance.
•Three pin connector eliminates faulty contact and improves
reliability against vibration and shock. Housing has a
reverse insertion prevention mechanism.
•Special grommet simplifies
mounting of the servo and has
an excellent cushioning effect.
•Six special adjustable splined horns.
•High 48.7 oz.in
(3.5kg-cm) maximum output torque allows
use
in almost any model.
Model number
Transmitter
Receiver
Servo
Switch, battery holder, etc.
FP-2GS
FP-T2GSx1
FP-R102GFx1
FP.S128.x2
TRANSMITTER FP-T2GS.
Operating method 2 stick system
Transmitting frequency 27MHz band, 72MHz band
Modulation system AM (amplitude modulation)
Power requirement
12V,
round penlight battery x 8
Receiver FP-R102GF
Receiving frequency
27MHz band, bands 1 to 6
72,75MHz
455kHz
3kHz/-3dB
550 yards (500m) on the ground
when used with FP-T2GS (At the
best radio wave condition of envi-
ronment)
4.8V
to
8.4V
7.2V/13mA,4.8V/33mA
1.46x
2.19
x
0.75
in
(37
x
55.5
x
19mm)
1.34
oz
(38g)
Intermediate frequency
Selectivity
Receiving range
Power supply
Current drain
Dimensions
Weight
SERVO FP-S128
Control system
Operating angle
Power requirement
Current drain (IDLE)
Output torque
Operating speed
Dimensions
+pulse width control
One side 45° or more
4.8V-6V
6.0V, 8mA (at idle)
48.7 oz.in. (3.5 kg-cm)
0.24 sec/60°
1.6x0.8x 1.6 in.
(40.5 x 20 x 40.5mm)
1.92oz. (53g)
Weight
HANDLING THE TRANSMITTER
•The name of each part of the transmitter is given in the figure.
Familiarize yourself with their operation.
•Remove the battery cover on the rear of the transmitter as
illustrated in the figure, and insert 8 round penlight batteries,
paying careful attention to their polarity.
•Extend the antenna fully, and set the power switch to the
ON position. The pointer of the level meter should deflect to
the green zone. If it fails to deflect, or deflects slowly, the
polarity of the batteries is incorrect, or the batteries are
faulty.
•Since the range of the radio waves will become short when
the pointer of the level meter deflects to the red zone, re-
place the batteries when the pointer only deflects to the
boundary between the green and red zones.
Comentarios a estos manuales