Futaba 14MZ Quick Start Guide - Helis Manual de usuario

Busca en linea o descarga Manual de usuario para Accesorios de comunicación Futaba 14MZ Quick Start Guide - Helis. Futaba 14MZ Quick Start Guide - Helis User Manual [fr] Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 4
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 0
When turning on the 14MZ, you must let the system cycle through before turning off.
There is a sequence that should be followed to get you started.
R5014DPS Receiver
First you should know the 14MZ receiver (R5014DPS) has
a different layout than the standard layout Futaba has
used in the past. After you have all your servos installed in
your helicopter, you’ll want to use one of these charts to
plug the proper servos into the R5014DPS receiver.
H-4 Swash All Others
Ch 1 Throttle Throttle
Ch 2 Rudder Rudder
Ch 3 Aileron (Left/Right Cyclic) Gyro
Ch 4 Elevator 1 (Fore/Aft Cyclic) Aileron (Left/Right Cyclic)
Ch 5 Pitch Elevator (Fore/Aft Cyclic)
Ch 6 Elevator 2 Pitch
Ch 7 Gyro Governor 1
Ch 8 Governor 1 Governor 2
Ch 9 Governor 2 Needle
Ch 10 Needle Auxiliary 3
Ch 11 Auxiliary 2 Auxiliary 2
Ch 12 Auxiliary 1 Auxiliary 1
CHOOSING MODEL TYPE AND SWASH TYPE
After turning on the power switch and pressing No for transmit. This will take you to the Home Page. Press Linkage Menu
then Model Select then press New, and then pressYes. Press on Swash Type and choose from one of the 7 different Swash
Types in the diagram that corresponds with the type of control system on your helicopter. You’ll be asked Check Change”, if
correct, press Yes.
After selecting the swash type you will come to the Frequency page. Select the frequency by pressing the Pink Box and then
select the frequency or channel you would like to be on for this particular model. After selecting the frequency, press Enter at
the top right hand corner of the screen. You’ll be asked to Check the change. If Yes, you’ll need to make sure you have your
battery plugged into the receiver but no power to the receiver. Once you press Yes, then turn on the power to the receiver to
program the receiver to the frequency you just selected. You must have the transmitter antenna very close to the receiver
antenna when doing this.
Please follow the steps in the manual on page (26) How to change the Frequency. Then you’ll need to turn off the power to
cycle through for the frequency to take affect.
Turn the system back on. Press Yes” for Transmit. This will take you to the Home Page to start setting everything up.
System Menu
Model Menu
Linkage Menu
Direct Keys
Vista de pagina 0
1 2 3 4

Indice de contenidos

Pagina 1

When turning on the 14MZ, you must let the system cycle through before turning off.There is a sequence that should be followed to get you started.R501

Pagina 2

SETTING SWASH MIXINGAt this time you should install and set up your servos as per the helicopter manufactures instructions.While at the Home Page, you

Pagina 3

ACTIVATING CONDITIONSFrom the Home Page press Model Menu, select Condition Select. In the red box you’ll see the word Normal. This is yournormal hover

Pagina 4

CHOOSING A PITCH AND THROTTLE CURVESYou have many types of curves tochoose from for both Throttle andPitch. From the Home Page, pressModel Menu and th

Comentarios a estos manuales

Sin comentarios